TQ210_BOARD_V3+Android4.0;HDMI输出问题

1.新板子；
2.插好重启和启动系统后再插HDMI线，都没有显示；
3.显示器和线都是好的，都已测试过；
以下是系统启动信息：

??DOK
##### EmbedSky BIOS for SKY210/TQ210 #####
This Board: SDRAM is 1024MB; LCD display size is: 800X480
Hit any key to stop autoboot:  0
SD Read NG
Fat32 file system initialzation failed!
Start Linux ......
NAND read: device 0 offset 0x500000, size 0x500000


5242880 bytes read: OK
Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 3.0.8-EmbedSky (root@embedsk-server) (gcc version 4.4.6 (for TQ210 EmbedSky Tech) ) #1 PREEMPT Fri Nov 2 14:35:24 CST 2012
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: TQ210
Truncating RAM at 40000000-5fffffff to -54ffffff (vmalloc region overlap).
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_dmc: source is sclk_a2m (0), rate is 200000000
sclk_onenand: source is hclk_dsys (1), rate is 166750000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
uclk1: source is mout_mpll (6), rate is 66700000
sclk_mixer: source is sclk_dac (0), rate is 54000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
sclk_fimd: source is mout_epll (7), rate is 80000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mfc: source is sclk_a2m (0), rate is 200000000
sclk_g2d: source is sclk_a2m (0), rate is 200000000
sclk_g3d: source is sclk_a2m (0), rate is 200000000
sclk_csis: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_pwi: source is ext_xtal (0), rate is 24000000
sclk_pwm: source is ext_xtal (0), rate is 24000000
s5p: 37748736 bytes system memory reserved for mfc at 0x3dc00000, 0-bank base(0x3dc00000)
s5p: 37748736 bytes system memory reserved for mfc at 0x52bf6000, 1-bank base(0x52bf6000)
s5p: 12582912 bytes system memory reserved for fimc0 at 0x51ff6000, 1-bank base(0x51ff6000)
s5p: 20275200 bytes system memory reserved for fimc1 at 0x50ca0000, 1-bank base(0x50ca0000)
s5p: 12582912 bytes system memory reserved for fimc2 at 0x500a0000, 1-bank base(0x500a0000)
s5p: 8388608 bytes system memory reserved for jpeg at 0x3d400000, 0-bank base(0x3d400000)
s5p: 12582912 bytes system memory reserved for fimd at 0x4f4a0000, 1-bank base(0x4f4a0000)
s5p: 1843200 bytes system memory reserved for pmem_gpu1 at 0x3d23e000, 0-bank base(0x3d23e000)
s5p: 8388608 bytes system memory reserved for g2d at 0x3ca3e000, 0-bank base(0x3ca3e000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 178248
Kernel command line: noinitrd root=/dev/mtdblock3 rootfstype=yaffs2 init=/init console=ttySAC0 lcd=X800Y480
user X800Y480 lcd.
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 458MB 244MB 0MB = 702MB total
Memory: 703544k/852120k available, 16232k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xff000000 - 0xffe00000   (  14 MB)
    vmalloc : 0xf5800000 - 0xfd000000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf5000000   ( 848 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0032000   ( 168 kB)
      .text : 0xc0032000 - 0xc06d751c   (6806 kB)
      .data : 0xc06d8000 - 0xc0720940   ( 291 kB)
       .bss : 0xc0720964 - 0xc085b458   (1259 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:208
VIC @fd000000: id 0x00041192, vendor 0x41
VIC @fd010000: id 0x00041192, vendor 0x41
VIC @fd020000: id 0x00041192, vendor 0x41
VIC @fd030000: id 0x00041192, vendor 0x41
sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 128784ms
Console: colour dummy device 80x30
Calibrating delay loop... 997.78 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
print_constraints: dummy:
NET: Registered protocol family 16
ENter s3c_adc_set_platdata,devname(s5pv210-adc)

S3C Power Management, Copyright 2004 Simtec Electronics
smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
S5PV210: Initializing architecture
s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
s3c24xx-pwm s3c24xx-pwm.2: tin at 33350000, tdiv at 33350000, tin=divclk, base 12
s3c24xx-pwm s3c24xx-pwm.3: tin at 33350000, tdiv at 33350000, tin=divclk, base 16
print_constraints: pd_tv_supply: 5000 mV normal
print_constraints: pd_lcd_supply: 5000 mV normal
print_constraints: pd_g3d_supply: 5000 mV normal
print_constraints: pd_mfc_supply: 5000 mV normal
print_constraints: pd_audio_supply: 5000 mV normal
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.5: using pins 118 (SDA) and 117 (SCL)
s3c-i2c s3c2440-i2c.0: slave address 0x10
s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2440-i2c.1: slave address 0x10
s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2440-i2c.2: slave address 0x10
s3c-i2c s3c2440-i2c.2: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource s5p_clocksource_timer
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 24576 bytes)
UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PMU: registered new PMU device of type 0
cpuidle: phy_regs_save:0x4f11f000
S5PV210 ADC driver, (c) 2010 Samsung Electronics
Loaded driver for PL330 DMAC-0 s3c-pl330
DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
ashmem: initialized
NTFS driver 2.1.30 [Flags: R/W DEBUG].
yaffs: yaffs built Nov  2 2012 14:35:00 Installing.
msgmni has been set to 1374
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
user a70 param
win->id=2, pmem_start=0x4f905000
s3cfb s3cfb: [fb2] dma: 0x4f905000, cpu: 0xf5c00000, size: 0x002ee000
FIMD src sclk = 166750000
s3cfb s3cfb: registered successfully
Start display and show logo
s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
console [ttySAC0] enabled
s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
TQ210 Beep driver successfully probed
TQ210 LEDs driver successfully probed

PA FB = 0x4F905000, bits per pixel = 32
screen width=800 height=480 va=0xef905000 pa=0x4f905000
xres_virtual = 800, yres_virtual = 960, xoffset = 0, yoffset = 0
fb_size=3072000
Back frameBuffer[0].VAddr=efa7c000 PAddr=4fa7c000 size=1536000
brd: module
s5p-ehci s5p-ehci: S5P EHCI Host Controller
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
lun0: LUN: removable file: (no medium)
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
mousedev: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
input: s3c_ts as /devices/virtual/input/input1
S5P Touchscreen driver, (c) 2008 Samsung Electronics
user a70 param
s3c_ts got loaded successfully : 10 bits
input: s3c_ts as /devices/virtual/input/input2
TSSEL : 1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
using rtc device, s3c, for alarms
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 250
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
gspca: v2.13.0 registered
mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics

S3C JPEG Driver, (c) 2007 Samsung Electronics
JPEG driver for S5PV210
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
S5PC11X HPD Driver, (c) 2010 Samsung Electronics
S5PC11X CEC Driver, (c) 2010 Samsung Electronics
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: HCIATH3K protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
usbcore: registered new interface driver bpa10x
Bluetooth: BlueFRITZ! USB driver ver 1.2
usbcore: registered new interface driver bfusb
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
usb 1-1: new high speed USB device number 2 using s5p-ehci
Bluetooth: Atheros AR30xx firmware driver ver 1.0
usbcore: registered new interface driver ath3k
cpuidle: usinGoodix-TS 2-005d: GT811 init info:X_MAX=800,Y_MAX=480,TRIG_MODE=RISING EDGE
usb 1-1.1: new low speed USB device number 3 using s5p-ehci
input: Goodix as /devices/virtual/input/input3
input: Logitech USB Optical Mouse as /devices/platform/s5p-ehci/usb1/1-1/1-1.1/1-1.1:1.0/input/input4
generic-usb 0003:046D:C05A.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-s5p-ehci-1.1/input0
usb 1-1.4: new high speed USB device number 4 using s5p-ehci
Goodix-TS 2-005d: GT811 Verion:0x2010
Goodix-TS 2-005d: Create proc entry success!
Goodix-TS 2-005d: Start Goodix in interrupt mode,Driver Modify Date:2012-01-05
probe_succeed goodix_ts_probe,916,drivers/input/touchscreen/gt811.c
s3c-rtc s3c64xx-rtc: setting system clock to 2000-02-17 17:26:11 UTC (950808371)
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
s5p-tvout s5p-tvout: hpd status is cable inserted
yaffs: dev is 32505859 name is "mtdblock3" rw
yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3"
option 1-1.4:1.0: GSM modem (1-port) converter detected
usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1.4:1.1: GSM modem (1-port) converter detected
usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
option 1-1.4:1.2: GSM modem (1-port) converter detected
usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
option 1-1.4:1.3: GSM modem (1-port) converter detected
usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB3
yaffs: yaffs_read_super: is_checkpointed 0
VFS: Mounted root (yaffs2 filesystem) on device 31:3.
Freeing init memory: 168K
init: cannot open '/initlogo.rle'
[init] SMB380 is error!
Acceleration_sensor: probe of Acceleration_sensor failed with error -1
input: Android Temperature Sensor as /devices/virtual/input/input5
rtusb init rt2870 --->
usbcore: registered new interface driver rt2870
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
android_usb: already disabled
/system/bin/sh: No controlling tty (open /dev/tty: No such device or address)
/system/bin/sh: warning: won't have full job control
adb_open
adb_bind_config
android_work: did not send uevent (0 0   (null))
android_work: sent uevent USB_STATE=CONNECTED
android_usb gadget: high speed config #1: android
android_work: sent uevent USB_STATE=CONFIGURED
root@android:/ # warning: `rild' uses 32-bit capabilities (legacy support in use)
asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok
asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok
PVR_KWarning): SysFinalise: Version string: SGX540 S5PC110 [543, drivers/gpu/pvr/s5pc110/sysconfig.c]
win->id=0, pmem_start=0x4f4a0000
s3cfb s3cfb: [fb0] dma: 0x4f4a0000, cpu: 0xf8000000, size: 0x00465000
s3cfb s3cfb: [fb1] dma: 0x4cc00000, cpu: 0xffa00000, size: 0x002ee000
er.ServerThread (2298): /proc/2284/oom_adj is deprecated, please use /proc/2284/oom_score_adj instead.
request_suspend_state: wakeup (3->0) at 66230439460 (2000-02-17 17:27:15.544692593 UTC)
acc_open
acc_release
dm9000 dm9000: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
dm9000 dm9000: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

130|root@android:/ # generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
generic-usb 0003:046D:C05A.0001: can't reset device, s5p-ehci-1.1/input0, status -71
hub 1-1:1.0: port 1 disabled by hub (EMI?), re-enabling...
usb 1-1.1: USB disconnect, device number 3
usb 1-1.1: new low speed USB device number 5 using s5p-ehci
input: Logitech USB Optical Mouse as /devices/platform/s5p-ehci/usb1/1-1/1-1.1/1-1.1:1.0/input/input6
generic-usb 0003:046D:C05A.0002: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-s5p-ehci-1.1/input0
EPLL Rate changes from 80000000 to 67738000
s3c2410_serial3: 1 input overrun(s)

logcat信息：

以下是拔了HDMI后发送的：
D/Vold    ( 2190): HDMI: offline
D/SecTVOutService( 2194): virtual void android::SecTVOutService::setHdmiStatus(uint32_t) HDMI cable status = 0
Dbfimc ( 2194): SecFimc::destroy()
D/Vold    ( 2190): HDMI: online
D/SecTVOutService( 2194): virtual void android::SecTVOutService::setHdmiStatus(uint32_t) HDMI cable status = 1
Dbfimc ( 2194): SecFimc::create(fimc_dev: 1, fimc_mode: 3, buf_num: 1)
Dbfimc ( 2194): fimc1 fd = 23
Ibhdmi ( 2194): =============== HDMI Audio  =============
Ibhdmi ( 2194): =  2CH_PCM 44100Hz audio supported      =
Ibhdmi ( 2194): ========= HDMI Mode & Color Space =======
Ibhdmi ( 2194): =  1. HDMI(YCbCr)                       =
Ibhdmi ( 2194): =  2. HDMI(RGB)                         =
Ibhdmi ( 2194): ===========    HDMI Rseolution   ========
Ibhdmi ( 2194): =  4. 480P_60_16_9 (0x04000000)=
Ibhdmi ( 2194): =  5. 480P_60_4_3(0x05000000)=
Ibhdmi ( 2194): =  6. 576P_50_16_9 (0x06000000)=
Ibhdmi ( 2194): =  7. 576P_50_4_3(0x07000000)=
Ibhdmi ( 2194): =  8. 720P_60 (0x08000000)=
Ibhdmi ( 2194): =  9. 720P_50 (0x09000000)=
Ibhdmi ( 2194): =  a. 1080P_60 (0x0a000000)=
Ibhdmi ( 2194): =  b. 1080P_50 (0x0b000000)=
Ibhdmi ( 2194): =  c. 1080I_60(0x0c000000)=
Ibhdmi ( 2194): =  d. 1080I_50(0x0d000000)=
Ibhdmi ( 2194): =========================================
Dbhdmi ( 2194): Device physical address is 1.0.0.0
E/        ( 2194): CECSendMessage() failed!
Ebhdmi ( 2194): CECAllocLogicalAddress() failed!!!
^CE/dhcpcd  ( 2642): timed out
D/Vold    ( 2190): HDMI: offline
D/SecTVOutService( 2194): virtual void android::SecTVOutService::setHdmiStatus(uint32_t) HDMI cable status = 0
Dbfimc ( 2194): SecFimc::destroy()

以下是插上HDMI发送的：
D/Vold    ( 2190): HDMI: online
D/SecTVOutService( 2194): virtual void android::SecTVOutService::setHdmiStatus(uint32_t) HDMI cable status = 1
Dbfimc ( 2194): SecFimc::create(fimc_dev: 1, fimc_mode: 3, buf_num: 1)
Dbfimc ( 2194): fimc1 fd = 23
Ibhdmi ( 2194): =============== HDMI Audio  =============
Ibhdmi ( 2194): =  2CH_PCM 44100Hz audio supported      =
Ibhdmi ( 2194): ========= HDMI Mode & Color Space =======
Ibhdmi ( 2194): =  1. HDMI(YCbCr)                       =
Ibhdmi ( 2194): =  2. HDMI(RGB)                         =
Ibhdmi ( 2194): ===========    HDMI Rseolution   ========
Ibhdmi ( 2194): =  4. 480P_60_16_9 (0x04000000)=
Ibhdmi ( 2194): =  5. 480P_60_4_3(0x05000000)=
Ibhdmi ( 2194): =  6. 576P_50_16_9 (0x06000000)=
Ibhdmi ( 2194): =  7. 576P_50_4_3(0x07000000)=
Ibhdmi ( 2194): =  8. 720P_60 (0x08000000)=
Ibhdmi ( 2194): =  9. 720P_50 (0x09000000)=
Ibhdmi ( 2194): =  a. 1080P_60 (0x0a000000)=
Ibhdmi ( 2194): =  b. 1080P_50 (0x0b000000)=
Ibhdmi ( 2194): =  c. 1080I_60(0x0c000000)=
Ibhdmi ( 2194): =  d. 1080I_50(0x0d000000)=
Ibhdmi ( 2194): =========================================
Dbhdmi ( 2194): Device physical address is 1.0.0.0
s3c2410_serial3: 1 input overrun(s)
E/        ( 2194): CECSendMessage() failed!
Ebhdmi ( 2194): CECAllocLogicalAddress() failed!!!

HMDI使用的A型接口的HDMI线

问题找到，是HDMI接口有多余焊锡，没弄干净，清理后OK了！

cctv8088 发表于 2013-6-17 12:22
问题找到，是HDMI接口有多余焊锡，没弄干净，清理后OK了！

晕，我们出厂时是测试过的哦，也目测过接口是否有锡珠之类的。搞不懂了。不过解决好了就好。