|
|
Start Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kern
el to SDRAM done,NOW, Booting Linux......
Uncompressing Linux.............................................................
...................................................... done, booting the kernel.
Linux version 2.6.25.8-EmbedSky (root@localhost.localdomain) (gcc version 4.3.3
(Sourcery G++ Lite 2009q1-176) ) #14 Sun Mar 28 22:26:47 CST 2010
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61056KB available (3356K code, 367K data, 104K init)
SLUB: Genslabs=12, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 152 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
S3C244X: Clock Support, DVS off
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs Mar 28 2010 20:38:53 Installing.
io scheduler noop registered (default)
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsula
tion enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
dm9000 Ethernet Driver, V1.30
dm9000 dm9000.0: eth%d: Invalid ethernet MAC address. Please set using ifconfig
eth0: dm9000 at c480e000,c4810004 IRQ 51 MAC: ff:ff:ff:ff:ff:ff (chip)
Linux video capture interface: v2.00
Driver 'sd' needs updating - please use bus_type methods
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 576 at 0x04800000
Bad eraseblock 581 at 0x048a0000
Bad eraseblock 620 at 0x04d80000
Bad eraseblock 1058 at 0x08440000
Bad eraseblock 2015 at 0x0fbe0000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00040000 : "EmbedSky_Board_uboot"
0x00200000-0x00600000 : "EmbedSky_Board_kernel"
0x00400000-0x0ff80000 : "EmbedSky_Board_yaffs2"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16
2008 UTC).
ASoC version 0.13.2
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 545 is bad
block 550 is bad
block 589 is bad
block 1027 is bad
block 1984 is bad
VFS: Mounted root (yaffs filesystem).
Freeing init memory: 104K
hwclock: settimeofday() failed: Invalid argument
input_polldev: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.
6.25.8-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/input-polldev.ko': invalid module format
mac80211: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25.
8-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/mac80211.ko': invalid module format
rt2x00lib: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25
.8-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/rt2x00lib.ko': invalid module format
rt2x00usb: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25
.8-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/rt2x00usb.ko': invalid module format
rt73usb: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25.8
-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/rt73usb.ko': invalid module format
zd1211rw: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25.
8-EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/zd1211rw.ko': invalid module format
ov9650: version magic '2.6.30.4-EmbedSky mod_unload ARMv4 ' should be '2.6.25.8-
EmbedSky mod_unload ARMv4 '
insmod: cannot insert '/lib/ov9650.ko': invalid module format
/dev/watchdog: No such file or directory
dm9000 dm9000.0: WARNING: no IRQ resource flags set.
eth0: link down
open device leds: No such file or directory
[01/Jan/1970:00:00:04 +0000] boa: server version Boa/0.94.13
[01/Jan/1970:00:00:04 +0000] boa: server built Jul 29 2009 at 14:27:34.
[01/Jan/1970:00:00:04 +0000] boa: starting server pid=334, port 80
ts_open: No such file or directory
我是自己从网上下载的源码linux2.6.25.8
照着那天嵌的开发教程移植的，烧进去后就出现上面的~！~而且屏幕显示是花的~哦！~~我的文件系统是用的天嵌自带的！~~请师傅们帮我解答下~~我是新手！~在自学中！~~谢谢！~ |
|
/1 
IP卡
狗仔卡
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡
