烧写NK.bin后无法启动

烧写NK_Q35_3Serial_20091224.bin后：

Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: u

USB host is connected. Waiting a download.

Addr: 0xC000000 ; Size: 0x1ABDC95
Read Bin Files StartAddr:0x80200000 ; Length: 0x1B217B4

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000  Length=0x1b217b4
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x1b217b4
RAM image 0xa 0x81d217b3
rom_offset=0x0.
ROMHDR at Address 80200044h
+WriteOSImageToBootMedia: g_dwTocEntry =1, ImageStart: 0x80200000, ImageLength: 0x1b217b4, LaunchAddr:0x80201000
INFO: OEMLaunch: Found chain extenstion: '' @ 0x80200000
Writing single region/multi-region update, dwBINFSPartLength: 28448692
CreatePartition: Enter CreatePartition for 0x21.
LastLogSector: Last log sector is: 0x7e5ff.
CreatePartition: Start = 0x1100, Num = 0xda00.
WriteMBR: MBR block = 0x10.
WriteData: Start = 0x0, Length = 0x1b217b4.
Updateded TOC!
CreatePartition: Enter CreatePartition for 0xb.
FindFreeSector: FreeSector is: 0xeb00 after processing part 0x21.
CreatePartition: Num sectors set to 0x6f600 to allow for compaction blocks.
CreatePartition: Start = 0xeb00, Num = 0x6f600.
WriteMBR: MBR block = 0x10.
TOC {
dwSignature: 0x434F544E
BootCfg {
  ConfigFlags: 0x2830
  BootDelay: 0x1
  ImageIndex: 1
  IP: 192.168.1.6
  MAC Address: 10:23:45:67:89:AB
  Port: 0.0.0.0
  SubnetMask: 255.255.255.0
}
ID[0] {
  dwVersion: 0x60000
  dwSignature: 0x45424F54
  String: 'eboot.nb0'
  dwImageType: 0x2
  dwTtlSectors: 0x400
  dwLoadAddress: 0x80038000
  dwJumpAddress: 0x80038000
  dwStoreOffset: 0x0
  sgList[0].dwSector: 0x400
  sgList[0].dwLength: 0x400
}
ID[1] {
  dwVersion: 0x1
  dwSignature: 0x43465348
  String: ''
  dwImageType: 0x2
  dwTtlSectors: 0xD90C
  dwLoadAddress: 0x80200000
  dwJumpAddress: 0x80201000
  dwStoreOffset: 0x0
  sgList[0].dwSector: 0x2100
  sgList[0].dwLength: 0xD90C
}
chainInfo.dwLoadAddress: 0X00000000
chainInfo.dwFlashAddress: 0X00000000
chainInfo.dwLength: 0X00000000
}
waitforconnect
INFO: OEMLaunch: Jumping to Physical Address 0x30201000h (Virtual Address 0x80201000h)...

C

重启后：
##### Eboot for TQ2440/SKY2440 #####
#####     www.embedsky.net     #####

Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 6.0 Built Jan 26 2010

Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.

Initiating image launch in 0 seconds.
Launching image from boot media ...
OEMPlatformInit: IMAGE_TYPE_RAMIMAGE
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x4
RAM image 0xa 0x80200003
+=OEMVerifyMemory+ dwStartAddr:0x80201000  dwLength:0x4
RAM image 0xa 0x80201003
waitforconnect
INFO: OEMLaunch: Jumping to Physical Address 0x30201000h (Virtual Address 0x80201000h)...

C

屏幕显示logo，无法启动CE，请问如何解决？

命令b-》命令9-》命令u，然后再试一下。

1# lpxc


同问。。。。

同问。。。
我也遇到同样的情况。
dashun_zju 发表于 2011-1-20 19:25 [/quote]