移植无线网卡的时候出现的问题

启动开发板时串口打印信息如下：

Start Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00300000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux............................................................................................................................ done, booting the kernel.
Linux version 2.6.30.4-EmbedSky (root@EmbedSky) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #10 Sun Sep 4 14:57:20 CST 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60748KB available (3500K code, 386K data, 120K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 936 bytes
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
yaffs Aug 25 2011 15:09:28 Installing.
msgmni has been set to 118
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
ide-cd driver 5.00
Driver 'sd' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address:10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c486e000,c4872004 IRQ 51 MAC: 10:23:45:67:89:ab (EmbedSky)
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 853 at 0x000006aa0000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
  No soundcards found.
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2009-05-06 00:49:06 UTC (1241570946)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 814 is bad
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 120K
rt2x00lib: Unknown symbol led_classdev_suspend
rt2x00lib: Unknown symbol led_classdev_unregister
rt2x00lib: Unknown symbol led_classdev_resume
rt2x00lib: Unknown symbol led_classdev_register
insmod: cannot insert '/lib/rt2x00lib.ko': unknown symbol in module or invalid parameter
rt2x00usb: Unknown symbol rt2x00lib_suspend
rt2x00usb: Unknown symbol rt2x00lib_probe_dev
rt2x00usb: Unknown symbol rt2x00lib_rxdone
rt2x00usb: Unknown symbol rt2x00lib_remove_dev
rt2x00usb: Unknown symbol rt2x00lib_txdone
rt2x00usb: Unknown symbol rt2x00queue_get_queue
rt2x00usb: Unknown symbol rt2x00lib_resume
insmod: cannot insert '/lib/rt2x00usb.ko': unknown symbol in module or invalid parameter
rt73usb: Unknown symbol rt2x00mac_add_interface
rt73usb: Unknown symbol crc_itu_t_table
rt73usb: Unknown symbol rt2x00mac_get_stats
rt73usb: Unknown symbol rt2x00usb_disable_radio
rt73usb: Unknown symbol rt2x00mac_set_key
rt73usb: Unknown symbol rt2x00usb_vendor_request_buff
rt73usb: Unknown symbol rt2x00usb_vendor_request_large_buff
rt73usb: Unknown symbol rt2x00usb_kick_tx_queue
rt73usb: Unknown symbol rt2x00usb_write_tx_data
rt73usb: Unknown symbol rt2x00mac_config_interface
rt73usb: Unknown symbol rt2x00mac_remove_interface
rt73usb: Unknown symbol rt2x00usb_vendor_request
rt73usb: Unknown symbol rt2x00usb_probe
rt73usb: Unknown symbol rt2x00mac_config
rt73usb: Unknown symbol rt2x00queue_get_queue
rt73usb: Unknown symbol rt2x00usb_suspend
rt73usb: Unknown symbol rt2x00usb_clear_entry
rt73usb: Unknown symbol rt2x00mac_conf_tx
rt73usb: Unknown symbol rt2x00mac_start
rt73usb: Unknown symbol rt2x00mac_stop
rt73usb: Unknown symbol rt2x00mac_configure_filter
rt73usb: Unknown symbol rt2x00usb_disconnect
rt73usb: Unknown symbol rt2x00mac_tx
rt73usb: Unknown symbol rt2x00usb_vendor_req_buff_lock
rt73usb: Unknown symbol rt2x00mac_get_tx_stats
rt73usb: Unknown symbol rt2x00usb_regbusy_read
rt73usb: Unknown symbol rt2x00usb_kill_tx_queue
rt73usb: Unknown symbol rt2x00usb_resume
rt73usb: Unknown symbol crc_itu_t
rt73usb: Unknown symbol rt2x00usb_uninitialize
rt73usb: Unknown symbol rt2x00usb_initialize
rt73usb: Unknown symbol rt2x00mac_bss_info_changed
insmod: cannot insert '/lib/rt73usb.ko': unknown symbol in module or invalid parameter
usbcore: registered new interface driver zd1211rw
Try to bring eth0 interface up ...
ifconfig eth0 hw ether 10:23:45:67:89:ab
eth0: link down
ifconfig eth0 192.168.1.6 netmask 255.255.255.0 up
add default gw 192.168.1.2
Done
[06/May/2009:00:49:14 +0000] boa: server version Boa/0.94.13
[06/May/2009:00:49:14 +0000] boa: server built Jul 29 2009 at 14:27:34.
[06/May/2009:00:49:14 +0000] boa: starting server pid=1014, port 80
cannot run '/usr/sbin/telnet': No such file or director

Please press Enter to activate this console.
哪位好心人解答下啊，搁浅好几天了....