如题，按照移植手册做的过程中出现的问题，网卡模块5个中3个失败，qtopia没有启动,是怎么回事
Start Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00300000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux.................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.4welcomelzh (root@lzh) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #14 Thu Apr 12 06:14:38 CST 2012
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60548KB available (3564K code, 391K data, 252K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 936 bytes
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS2 version 2.2. (NAND) (SUMMARY) 漏 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
yaffs Apr 9 2012 04:15:15 Installing.
msgmni has been set to 118
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Failed to allocate video RAM: -12
s3c2410-lcd: probe of s3c2410-lcd failed with error -12
backlight initialized
GPIO-Control initialized
PWM-Test initialized
adc initialized
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
ide-cd driver 5.00
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c4872000,c4876004 IRQ 51 MAC: 10:23:45:67:89:ab (EmbedSky)
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 660 at 0x000005280000
Bad eraseblock 685 at 0x0000055a0000
Bad eraseblock 695 at 0x0000056e0000
Bad eraseblock 720 at 0x000005a00000
Bad eraseblock 854 at 0x000006ac0000
Bad eraseblock 1167 at 0x0000091e0000
Bad eraseblock 1220 at 0x000009880000
Bad eraseblock 1456 at 0x00000b600000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
mice: PS/2 mouse device common for all mice
TQ2440 TouchScreen successfully loaded
input: TQ2440 TouchScreen as /class/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
#0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2008-11-13 00:09:50 UTC (1226534990)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 252K
Try to bring eth0 interface up ...
ifconfig eth0 hw ether C8:0A:A9:73:13:BF
eth0: link down
ifconfig eth0 192.168.11.53 netmask 255.255.255.0 up
add default gw 192.168.11.254
Done
[13/Nov/2008:00:09:55 +0000] boa: server version Boa/0.94.13
[13/Nov/2008:00:09:55 +0000] boa: server built Jul 29 2009 at 14:27:34.
[13/Nov/2008:00:09:55 +0000] boa: starting server pid=1024, port 80
Start Qtopia-2.2.0
Segmentation fault
rt2x00lib: Unknown symbol led_classdev_suspend
rt2x00lib: Unknown symbol led_classdev_unregister
rt2x00lib: Unknown symbol led_classdev_resume
rt2x00lib: Unknown symbol led_classdev_register
insmod: can't insert '/lib/rt2x00lib.ko': unknown symbol in module, or unknown parameter
rt2x00usb: Unknown symbol rt2x00lib_suspend
rt2x00usb: Unknown symbol rt2x00lib_probe_dev
rt2x00usb: Unknown symbol rt2x00lib_rxdone
rt2x00usb: Unknown symbol rt2x00lib_remove_dev
rt2x00usb: Unknown symbol rt2x00lib_txdone
rt2x00usb: Unknown symbol rt2x00queue_get_queue
rt2x00usb: Unknown symbol rt2x00lib_resume
insmod: can't insert '/lib/rt2x00usb.ko': unknown symbol in module, or unknown parameter
rt73usb: Unknown symbol rt2x00mac_add_interface
rt73usb: Unknown symbol crc_itu_t_table
rt73usb: Unknown symbol rt2x00mac_get_stats
rt73usb: Unknown symbol rt2x00usb_disable_radio
rt73usb: Unknown symbol rt2x00mac_set_key
rt73usb: Unknown symbol rt2x00usb_vendor_request_buff
rt73usb: Unknown symbol rt2x00usb_vendor_request_large_buff
rt73usb: Unknown symbol rt2x00usb_kick_tx_queue
rt73usb: Unknown symbol rt2x00usb_write_tx_data
rt73usb: Unknown symbol rt2x00mac_config_interface
rt73usb: Unknown symbol rt2x00mac_remove_interface
rt73usb: Unknown symbol rt2x00usb_vendor_request
rt73usb: Unknown symbol rt2x00usb_probe
rt73usb: Unknown symbol rt2x00mac_config
rt73usb: Unknown symbol rt2x00queue_get_queue
rt73usb: Unknown symbol rt2x00usb_suspend
rt73usb: Unknown symbol rt2x00usb_clear_entry
rt73usb: Unknown symbol rt2x00mac_conf_tx
rt73usb: Unknown symbol rt2x00mac_start
rt73usb: Unknown symbol rt2x00mac_stop
rt73usb: Unknown symbol rt2x00mac_configure_filter
rt73usb: Unknown symbol rt2x00usb_disconnect
rt73usb: Unknown symbol rt2x00mac_tx
rt73usb: Unknown symbol rt2x00usb_vendor_req_buff_lock
rt73usb: Unknown symbol rt2x00mac_get_tx_stats
rt73usb: Unknown symbol rt2x00usb_regbusy_read
rt73usb: Unknown symbol rt2x00usb_kill_tx_queue
rt73usb: Unknown symbol rt2x00usb_resume
rt73usb: Unknown symbol crc_itu_t
rt73usb: Unknown symbol rt2x00usb_uninitialize
rt73usb: Unknown symbol rt2x00usb_initialize
rt73usb: Unknown symbol rt2x00mac_bss_info_changed
insmod: can't insert '/lib/rt73usb.ko': unknown symbol in module, or unknown parameter
Can't open framebuffer device /dev/fb0
Can't open framebuffer device /dev/fb0
driver cannot connect
usbcore: registered new interface driver zd1211rw
Please press Enter to activate this console.
[root@EmbedSky /]# cat /etc/init.d/rcS
#!/bin/sh
PATH=/sbin:/bin:/usr/sbin:/usr/bin
runlevel=S
prevlevel=N
umask 022
export PATH runlevel prevlevel
#
# Trap CTRL-C &c only in this shell so we can interrupt subprocesses.
#
mount -a
mkdir -p /dev/pts
mount -t devpts devpts /dev/pts
echo /sbin/mdev > /proc/sys/kernel/hotplug
mdev -s
mkdir -p /var/lock
mkdir /dev/fb /dev/v4l
ln -s /dev/fb0 /dev/fb/0
ln -s /dev/video0 /dev/v4l/video0
ln -s /dev/ts0 /dev/h3600_tsraw
#hwclock -s
EmbedSky_wdg &
ifconfig lo 127.0.0.1
net_set &
/etc/rc.d/init.d/httpd start
export set TSLIB_TSDEVICE=/dev/event0
export set TSLIB_CONFFILE=/etc/ts.conf
export set TSLIB_PLUGINDIR=/lib/ts
export set TSLIB_CALIBFILE=/etc/pointercal
export set HOME=/root
export set QTDIR=/opt/Qtopia
export set QPEDIR=/opt/Qtopia
export set KDEDIR=/opt/kde
export set QWS_KEYBOARD="TTY:/dev/tty1"
export set QWS_MOUSE_PROTO="TPanel:/dev/event0 USB:/dev/mouse0"
export set PATH=$QPEDIR/bin:$PATH
export set LD_LIBRARY_PATH=$QTDIR/lib:$QPEDIR/lib
qtopia &
insmod /lib/input-polldev.ko
insmod /lib/mac80211.ko
#TL-WN321G+
insmod /lib/rt2x00lib.ko
insmod /lib/rt2x00usb.ko
insmod /lib/rt73usb.ko
#TL-WN322G+
insmod /lib/zd1211rw.ko
#insmod /lib/ov9650.ko
#/etc/rc.d/init.d/leds start
#/etc/rc.d/init.d/netd start
/bin/hostname -F /et
|
/1 
IP卡
狗仔卡
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡