TQ2440 nand flash 烧写了内核之后启动不了

我在linux上nor flash 上通过usb向nand flash 烧写u-boot和内核（都是出厂镜像里的）。nand flash 上的u-boot可以正常启动，内核会停在某一个地方。Linux-2.6.30.4 和 Linux-2.6.25.8都试过，都这样。
内核启动过程：
##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !
Booting Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x0030000.
Uncompressing Linux...............................................
Linux version 2.6.30.4-EmbedSky (root@EmbedSky) (gcc version 4.3.0
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: TQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 z
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pag6
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc c0
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing pending status 02000000
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 59860KB available (4320K code, 448K data, 240K init, 0K h)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb

图片太小，再贴下：

usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs May 31 2010 10:39:00 Installing.
msgmni has been set to 117
alg: No test for stdrng (krng)
io scheduler noop registered (default)
Console: switching to colour frame buffer device 60x17
fb0: s3c2410fb frame buffer device
backlight initialized
GPIO-Control initialized
PWM-Test initialized
adc initialized
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a0
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a0
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a0
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c4814000,c4818004 IRQ 51 MAC: 10:23:45:67:89:ab )
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 s
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 2)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 84 at 0x000000a80000
Bad eraseblock 1497 at 0x00000bb20000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus n1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.30.4-EmbedSky ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to s
mice: PS/2 mouse device common for all mice
TQ2440 TouchScreen successfully loaded
input: TQ2440 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
cx231xx v4l2 driver loaded.
usbcore: registered new interface driver cx231xx
usbcore: registered new interface driver usbvision
USBVision USB Video Device Driver for Linux : 0.9.10
usbcore: registered new interface driver ov511
ov511: v1.64 for Linux 2.5:ov511 USB Camera Driver
SE401 usb camera driver version 0.24 registering
usbcore: registered new interface driver se401
usbcore: registered new interface driver stv680
stv680 [usb_stv680_init:1550]
STV(i): usb camera driver version v0.25 registering<6>stv680: v0.r
w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chipc
usbcore: registered new interface driver w9968cf
usbcore: registered new interface driver zr364xx
zr364xx: Zoran 364xx
usbcore: registered new interface driver stkwebcam
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47pre9
usbcore: registered new interface driver sn9c102
et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.9
usbcore: registered new interface driver et61x251
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/73.
pwc: Also supports the Askey VC010, various Logitech Quickcams, S,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionit.
usbcore: registered new interface driver Philips webcam
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chi0
usbcore: registered new interface driver zc0301
gspca: main v2.5.0 registered
usbcore: registered new interface driver conex
conex: registered
usbcore: registered new interface driver etoms
etoms: registered
usbcore: registered new interface driver finepix
finepix: registered
usbcore: registered new interface driver mars
mars: registered
usbcore: registered new interface driver mr97310a
mr97310a: registered
usbcore: registered new interface driver ov519
ov519: registered
usbcore: registered new interface driver ov534
ov534: registered
usbcore: registered new interface driver pac207
pac207: registered
usbcore: registered new interface driver pac7311
pac7311: registered
usbcore: registered new interface driver sonixb
sonixb: registered
usbcore: registered new interface driver sonixj
sonixj: registered
usbcore: registered new interface driver spca500
spca500: registered
usbcore: registered new interface driver spca501
spca501: registered
usbcore: registered new interface driver spca505
spca505: registered
usbcore: registered new interface driver spca506
spca506: registered
usbcore: registered new interface driver spca508
spca508: registered
usbcore: registered new interface driver spca561
spca561: registered
usbcore: registered new interface driver sq905
sq905: registered
usbcore: registered new interface driver sq905c
sq905c: registered
usbcore: registered new interface driver sunplus
sunplus: registered
usbcore: registered new interface driver stk014
stk014: registered
usbcore: registered new interface driver t613
t613: registered
usbcore: registered new interface driver tv8532
tv8532: registered
usbcore: registered new interface driver vc032x
vc032x: registered
usbcore: registered new interface driver zc3xx
zc3xx: registered
usbcore: registered new interface driver ALi m5602
ALi m5602: registered
usbcore: registered new interface driver STV06xx
STV06xx: registered
usbcore: registered new interface driver ibmcam
usbcore: registered new interface driver ultracam
konicawc: v1.4:Konica Webcam driver
usbcore: registered new interface driver konicawc
usbcore: registered new interface driver vicam
quickcam_messenger: v0.01:Logitech Quickcam Messenger USB
usbcore: registered new interface driver QCM
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2009-06-27 23:10)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 45 is bad
block 1458 is bad
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 240K
Warning: unable to open an initial console.
Failed to execute /linuxrc.  Attempting defaults...
Kernel panic - not syncing: No init found.  Try passing init= opt.
Backtrace:
[<c0048fd4>] (dump_backtrace+0x0/0x10c) from [<c0349710>] (dump_s)
r7:00000000 r6:c04b7d40 r5:c04b7700 r4:c0480248
[<c03496f8>] (dump_stack+0x0/0x1c) from [<c0349760>] (panic+0x4c/)
[<c0349714>] (panic+0x0/0x124) from [<c00444f0>] (init_post+0xec/)
r3:00000000 r2:c388be00 r1:c04ee000 r0:c0411a8c
[<c0044404>] (init_post+0x0/0x178) from [<c000847c>] (kernel_init)
r5:c001ec40 r4:c001f05c
[<c00083b0>] (kernel_init+0x0/0xf4) from [<c0059f30>] (do_exit+0x)
r7:00000000 r6:00000000 r5:00000000 r4:00000000
求大神指导

已经解决，原来没烧内核。

学习学习

shapolang 发表于 2013-9-15 22:33
已经解决，原来没烧内核。

亲，问题解决了请将帖子类型修改为“已解决”（请参考：http://www.armbbs.net/forum.php?mod=viewthread&tid=15200）。