TQ210更新NAND FLASH上的uboot

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky TFTP download mode     #####

[1] Download u-boot.bin to Nand Flash
[2] Download Eboot (eboot.nb0) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Set TFTP parameters(PC IP,TQ210 IP,Mask IP...)
[p] Test network (TQ210 Ping PC's IP)
[r] Reboot u-boot
[s] Download STEPLDR.nb1 to Nand Flash
[t] Test Linux Image (zImage)
[q] Return main Menu
Enter your selection: 1
dm9000 i/o: 0x88000000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
could not establish link
TFTP from server 192.168.1.103; our IP address is 192.168.1.80
Filename 'u-boot.bin'.
Load address: 0xc0008000
Loading: *
ARP Retry count exceeded; starting again
TFTP from server 192.168.1.103; our IP address is 192.168.1.80
Filename 'u-boot.bin'.
Load address: 0xc0008000
Loading: *
ARP Retry count exceeded; starting again
TFTP from server 192.168.1.103; our IP address is 192.168.1.80
Filename 'u-boot.bin'.
Load address: 0xc0008000
Loading: #################################################################
         ################
done
Bytes transferred = 409600 (0x64000)

NAND erase: device 0 offset 0x0, size 0x100000
Erasing at 0xe0000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x64000
Main area read (4 blocks):
Checksum is calculated.
Main area write (4 blocks):
524288 bytes written: OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky TFTP download mode     #####

[1] Download u-boot.bin to Nand Flash
[2] Download Eboot (eboot.nb0) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Set TFTP parameters(PC IP,TQ210 IP,Mask IP...)
[p] Test network (TQ210 Ping PC's IP)
[r] Reboot u-boot
[s] Download STEPLDR.nb1 to Nand Flash
[t] Test Linux Image (zImage)
[q] Return main Menu
Enter your selection:

U-Boot 1.3.4 (Feb  3 2013 - 20:55:06) for TQ210


CPU:  S5PV210@1000MHz(OK)
        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
        MPLL = 667MHz, EPLL = 80MHz
                       HclkDsys = 166MHz, PclkDsys = 83MHz
                       HclkPsys = 133MHz, PclkPsys = 66MHz
                       SCLKA2M  = 200MHz
Serial = CLKUART
Board:   TQ210
DRAM:     1 GB

##### 2beanet BIOS for VXB210/TQ210 #####
This Board: SDRAM is 1024MB; LCD display size is: 800X480
Hit any key to stop autoboot:  0

{:2_148