SD卡自动更新问题

*** Warning - bad CRC or NAND, using default environment

##### EmbedSky BIOS for SKY6410/TQ6410 #####
This Board: SDRAM is 256MB; LCD display size is: 480X272
Press Space key to Download Mode !
SD and FAT initialize success!
file length is 0x36d.
condition=INSTALL
OSType=LINUX
beep state=ON

bootloader=images\bootloader\u-boot_nand_256MB_T43_V1.3.bin
file length is 0x64000.

NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x0 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0xd000

Writing data at 0xc000 -- 100% complete.
53248 bytes written: OK

logodir=images\logo\logo_T43.bin
file length is 0x3fc00.

NAND erase: device 0 offset 0x100000, size 0x200000
Erasing at 0x280000 -- 100% complete.
OK

NAND write: device 0 offset 0x100000, size 0x8000

Writing data at 0x107000 -- 100% complete.
32768 bytes written: OK

Linux zImage=images\linux\zImage_3.0_T43_V1.3.bin
file length is 0x337c80.

NAND erase: device 0 offset 0x300000, size 0x400000
Erasing at 0x680000 -- 100% complete.
OK

NAND write: device 0 offset 0x300000, size 0x67000

Writing data at 0x366000 -- 100% complete.
421888 bytes written: OK

Linux rootfs=images\root\root_TQ6410_PDA_MLC2GB_V1.3.ubi

NAND erase: device 0 offset 0x700000, size 0x7f900000
Erasing at 0x7ff80000 -- 100% complete.
OK
Creating 1 MTD partitions on "nand0":
0x00700000-0x80000000 : "mtd=4"
Creating dynamic volume rootfs of size 2083995648
Volume "rootfs" found at volume id 0.
UBIFS image length is 0x485a000, Write UBIFS to rootfs, please wait.
Writing 100% complete.
UBIFS write compilete!
Saving Environment to NAND...
Erasing Nand...
Erasing at 0x80000 -- 100% complete.
Writing to Nand... done
Start Linux ......
NAND read: device 0 offset 0x300000, size 0x400000

................................................................................
.....................
4194304 bytes read: OK
Boot with zImage

Starting kernel ...
到这里就停住了
没有Uncompressing Linux...及后面的信息出现。
屏幕就是白屏

我的卡是金士顿4g的卡

亲，在串口信息中显示内核读到内存中的容量和烧写的实际容量不一样哦。你是不是修改过什么东西啊？
Linux zImage=images\linux\zImage_3.0_T43_V1.3.bin
file length is 0x337c80.

NAND erase: device 0 offset 0x300000, size 0x400000
Erasing at 0x680000 -- 100% complete.
OK

NAND write: device 0 offset 0x300000, size 0x67000

Writing data at 0x366000 -- 100% complete.
421888 bytes written: OK

亚瑟王 发表于 2013-2-4 15:03
亲，在串口信息中显示内核读到内存中的容量和烧写的实际容量不一样哦。你是不是修改过什么东西啊？
Linux  ...

重新做一遍就好了  请问亚瑟王6410怎么通过路由访问网路，我现在局域网是ping通了，网页打不开

木♀木 发表于 2013-2-4 16:56
重新做一遍就好了  请问亚瑟王6410怎么通过路由访问网路，我现在局域网是ping通了，网页打不开

亲，你需要设置正确的DNS，Linux的话修改文件系统中的/etc/resolv.conf文件

亚瑟王 发表于 2013-2-5 13:28
亲，你需要设置正确的DNS，Linux的话修改文件系统中的/etc/resolv.conf文件

谢谢亚瑟王，设成路由的IP就可以了

木♀木 发表于 2013-2-5 17:28
谢谢亚瑟王，设成路由的IP就可以了

好的，
亲，问题解决了，请将帖子类型改为“已解决”（在“分类”栏目下可以修改）。

亚瑟王 发表于 2013-2-5 20:02
好的，
亲，问题解决了，请将帖子类型改为“已解决”（在“分类”栏目下可以修改）。

请问分类在哪里啊  米找到啊