TQ210开机启动android4.0，在内核检测时停住了，怎么回事？？

今天TQ210开机的时候遇到了一个问题。上电时原本跑Android系统，但是发现画面一直停住在TQ那个大logo画面。然后我连上串口查看了终端打印下来的东西：
……（省略前面一部分）
Start display and show logo
s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
console [ttySAC0] enabled
s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
TQ210 Beep driver successfully probed
TQ210 LEDs driver successfully probed
PA FB = 0x4F905000, bits per pixel = 32
screen width=800 height=480 va=0xef905000 pa=0x4f905000
xres_virtual = 800, yres_virtual = 960, xoffset = 0, yoffset = 0
fb_size=3072000
Back frameBuffer[0].VAddr=efa7c000 PAddr=4fa7c000 size=1536000
brd: module loaded
loop: module loaded
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 4 MTD partitions on "s5pv210-nand":
0x000000000000-0x000000100000 : "Bootloader"
0x000000100000-0x000000300000 : "LOGO"
0x000000500000-0x000000a00000 : "Kernel"
0x000000a00000-0x000040000000 : "ROOTFS"
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver, V1.31
eth0: dm9000b at f5830300,f5832304 IRQ 42 MAC: 00:09:c2:ff:ec:68 (platform data)
hso: drivers/net/usb/hso.c: Option Wireless
usbcore: registered new interface driver hso
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: S5P EHCI Host Controller
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
lun0: LUN: removable file: (no medium)
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
mousedev: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
（信息就打印到这里，再没有了）

我找出以前保存的终端打印信息，是下面这样子的：
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
input: s3c_ts as /devices/virtual/input/input1
S5P Touchscreen driver, (c) 2008 Samsung Electronics
user a70 param
s3c_ts got loaded successfully : 10 bits
input: s3c_ts as /devices/virtual/input/input2
TSSEL : 1
……（省略后边部分）

对比下发现，打印信息停在了input: gpio-keys as /devices/platform/gpio-keys/input/input0，而没有后边的input: s3c_ts as /devices/virtual/input/input1。
小弟不知道这是出了什么问题。麻烦哪位知道的帮忙解答一下。。
感激不尽。。

我们的板子 好像还没有过见过这个问题的。你提是不是我们光盘内核与文件系统，如果是你试下改用2.3的看下，实在不行可以邮回来我们看下

TQ-ZQL 发表于 2013-4-25 11:32
我们的板子 好像还没有过见过这个问题的。你提是不是我们光盘内核与文件系统，如果是你试下改用2.3的看下， ...

是的，用的是你们的Android4.0内核和文件系统。因为遇到了，所以想知道问题出在哪里。

我也遇到了类似的问题，android4.0卡在了启动界面，没刷过系统，是不是太热了，因为板子很热，求版主给力

我想是启动的参数改错了吧