TQ2440装自带光盘里的wince，按部就班安装不成功求解

TQ2440装自带光盘里的wince，按视频里的方法安装，linux的可以安装使用，win测的安装到最后一 步，安装文件系统时，DNW软件显示进度条过半之后，cecureCRT软件就报错了。如下所示，求解，板子刚买的。
Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 6.0 Built Jun 12 2010

Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.

Initiating image launch in 1 seconds.
Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: b
Reserving Blocks [0x0 - 0xf] ...
...reserve complete.

Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: 9
Enter TQ2440 FastLowLevelFormat [0x10, 0x7ff].
Format TQ2440 Nand Flash: found a bad block (0x3d2) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x4d7) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x5cc) - skipping...
Format TQ2440 Nand Flash: ...erase complete.
WriteMBR: MBR block = 0x10.
BP_FastLowLevelFormat: Done.


Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: u

USB host is connected. Waiting a download.

Addr: 0xC000000 ; Size: 0x1ED2BA5
Read Bin Files StartAddr:0x80200000 ; Length: 0x1F44084

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000  Length=0x1f44084
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x1f44084
RAM image 0xa 0x82144083
ERROR: Checksum failure (expected=0x1755CCB  computed=0x15369BE)
****** Checksum failure on record 154, ABORT!!! ******

我的解决了，重新上传一份文件系统，用这个就可以成功

我的权限不够，这里给一个下载链接，有用到的兄弟自己下载，谁的权限高也可以上传到坛子里

链接：http://download.csdn.net/detail/zhangleiat185/6952371

我查了下，这问题也不止我一个人出现，怎么都没解决呢

我说一下步骤哈，你对一下：
1、从nor启动按9格式化nand
2、按1烧stepldr
3、按2烧eboot
4、从nand启动，b->9->u烧写nk.bin
请先使用光盘中的镜像烧写确认板子硬件没问题。

TQ-lkp 发表于 2013-8-13 09:16
我说一下步骤哈，你对一下：
1、从nor启动按9格式化nand
2、按1烧stepldr

我的步骤比你多了一步，烧eboot之后，我还烧了logo进去，视频里是这么做的，其它步骤完全一样。烧的就是和视频一起的那个光盘里的wince，其他东西也都是这光盘里的。然道真是硬件问题？？？

换了个wince文件系统来装，装成功了

NeroDevil 发表于 2013-8-13 21:08
换了个wince文件系统来装，装成功了

你好，我也遇到了这样的问题Checksum failure on record 154, ABORT!!!

请问你成功的是用得哪个镜像啊

NeroDevil 发表于 2013-8-13 21:08
换了个wince文件系统来装，装成功了

请问这是怎么回事？？遇到同样问题！裸机程序也无法运行，是不是硬件问题？急求解！！！谢谢呀

求解！！！！！！！！！！

我也遇到了，CE和LINUX都烧不进，每一步都按说明书做的，说明书看烂了，也没用，菜鸟求解

求LZ烧成功的WINCE的文件系统，我也出现了和LZ一样的问题

同求，我也遇到下载NK时，加载不成功；

不懂。。。。。

原来是WinCE的程序有问题   安装前面的换了一个bin成功下载