天嵌 ARM开发社区

 找回密码
 注册
查看: 6446|回复: 13

TQ2440装自带光盘里的wince,按部就班安装不成功求解

[复制链接]
NeroDevil 发表于 2013-8-13 01:25:31 | 显示全部楼层 |阅读模式
本帖最后由 NeroDevil 于 2013-8-13 01:26 编辑

TQ2440装自带光盘里的wince,按视频里的方法安装,linux的可以安装使用,win测的安装到最后一 步,安装文件系统时,DNW软件显示进度条过半之后,cecureCRT软件就报错了。如下所示,求解,板子刚买的。
Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 6.0 Built Jun 12 2010

Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.

Initiating image launch in 1 seconds.
Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: b
Reserving Blocks [0x0 - 0xf] ...
...reserve complete.

Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: 9
Enter TQ2440 FastLowLevelFormat [0x10, 0x7ff].
Format TQ2440 Nand Flash: found a bad block (0x3d2) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x4d7) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x5cc) - skipping...
Format TQ2440 Nand Flash: ...erase complete.
WriteMBR: MBR block = 0x10.
BP_FastLowLevelFormat: Done.


Ethernet Boot Loader Configuration:

0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now

Enter your selection: u

USB host is connected. Waiting a download.

Addr: 0xC000000 ; Size: 0x1ED2BA5
Read Bin Files StartAddr:0x80200000 ; Length: 0x1F44084

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000  Length=0x1f44084
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x1f44084
RAM image 0xa 0x82144083
ERROR: Checksum failure (expected=0x1755CCB  computed=0x15369BE)
****** Checksum failure on record 154, ABORT!!! ******
zhangleiat185 发表于 2014-2-23 17:25:31 | 显示全部楼层
本帖最后由 zhangleiat185 于 2014-2-23 17:42 编辑

我的解决了,重新上传一份文件系统,用这个就可以成功

我的权限不够,这里给一个下载链接,有用到的兄弟自己下载,谁的权限高也可以上传到坛子里

链接:http://download.csdn.net/detail/zhangleiat185/6952371
回复 支持 2 反对 0

使用道具 举报

 楼主| NeroDevil 发表于 2013-8-13 01:28:06 | 显示全部楼层
我查了下,这问题也不止我一个人出现,怎么都没解决呢
TQ-lkp 发表于 2013-8-13 09:16:44 | 显示全部楼层
我说一下步骤哈,你对一下:
1、从nor启动按9格式化nand
2、按1烧stepldr
3、按2烧eboot
4、从nand启动,b->9->u烧写nk.bin
请先使用光盘中的镜像烧写确认板子硬件没问题。
 楼主| NeroDevil 发表于 2013-8-13 13:00:24 | 显示全部楼层
本帖最后由 NeroDevil 于 2013-8-13 13:01 编辑
TQ-lkp 发表于 2013-8-13 09:16
我说一下步骤哈,你对一下:
1、从nor启动按9格式化nand
2、按1烧stepldr

我的步骤比你多了一步,烧eboot之后,我还烧了logo进去,视频里是这么做的,其它步骤完全一样。烧的就是和视频一起的那个光盘里的wince,其他东西也都是这光盘里的。然道真是硬件问题???
 楼主| NeroDevil 发表于 2013-8-13 21:08:05 | 显示全部楼层
换了个wince文件系统来装,装成功了
zbffff 发表于 2013-8-30 18:26:48 | 显示全部楼层
NeroDevil 发表于 2013-8-13 21:08
换了个wince文件系统来装,装成功了

你好,我也遇到了这样的问题Checksum failure on record 154, ABORT!!!

请问你成功的是用得哪个镜像啊
zhangliyun9120 发表于 2013-9-17 22:11:18 | 显示全部楼层
NeroDevil 发表于 2013-8-13 21:08
换了个wince文件系统来装,装成功了

请问这是怎么回事??遇到同样问题!裸机程序也无法运行,是不是硬件问题?急求解!!!谢谢呀
zhangliyun9120 发表于 2013-9-17 22:12:20 | 显示全部楼层
求解!!!!!!!!!!
laoyang12345 发表于 2014-2-7 10:33:54 | 显示全部楼层
我也遇到了,CE和LINUX都烧不进,每一步都按说明书做的,说明书看烂了,也没用,菜鸟求解
zhangleiat185 发表于 2014-2-13 17:44:04 | 显示全部楼层
求LZ烧成功的WINCE的文件系统,我也出现了和LZ一样的问题
tinkzel 发表于 2014-2-19 19:14:49 | 显示全部楼层
同求,我也遇到下载NK时,加载不成功;
xubeiping0930 发表于 2014-8-15 22:02:57 | 显示全部楼层
原来是WinCE的程序有问题   安装前面的换了一个bin成功下载
您需要登录后才可以回帖 登录 | 注册

本版积分规则

关闭

i.MX8系列ARM cortex A53 M4 工控板上一条 /1 下一条

Archiver|手机版|小黑屋|天嵌 嵌入式开发社区 ( 粤ICP备11094220号 )

GMT+8, 2024-3-29 22:13 , Processed in 1.046875 second(s), 20 queries .

Powered by Discuz! X3.4

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表