TQ210 V3 烧录问题

用光盘中“出厂烧录镜像合集”进行烧录后，重新启动，系统起不来，串口打印信息如下：
##### EmbedSky BIOS for SKY210/TQ210 #####
This Board: SDRAM is 1024MB; LCD display size is: 800X480
Hit any key to stop autoboot:  0
Start Linux ......
NAND read: device 0 offset 0x500000, size 0x500000


5242880 bytes read: OK
Boot with zImage

Starting kernel ...

Uncompressing Linux...

uncompression error

-- System haltedD?8痧

按1,重新烧写个uboot看下。然后重启板子再烧。
确定没有用错镜像？

[t] Test Linux Image (zImage) 对内核文件进行测试，

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 9

NAND scrub: device 0 whole chip
Warning: scrub option will erase all factory set bad blocks!
         There is no reliable way to recover them.
         Use this command only for testing purposes if you
         are sure of what you are doing!

Really scrub this NAND flash? <y/N>
y

Erasing at 0x147a0000 --  32% complete.
nand0: MTD Erase failure: -5
Erasing at 0x3ffe0000 -- 100% complete.
Scanning device for bad blocks
OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 1
OTG cable Connected!
Now, Waiting for DNW to transmit data

Now, Downloading [ADDRESS:0xc0008000,TOTAL:0x6c000]
Please waiting ......Download Done!!
Download Address: 0xc0008000, Download Filesize:0x6c000
Checksum is being calculated.Checksum O.K.

NAND erase: device 0 offset 0x0, size 0x100000
Erasing at 0xe0000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x6c000
Main area read (4 blocks):
Checksum is calculated.
Main area write (4 blocks):
524288 bytes written: OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 3
OTG cable Connected!
Now, Waiting for DNW to transmit data

Now, Downloading [ADDRESS:0xc0008000,TOTAL:0x498cd4]
Please waiting .........................................................................Download Done!!
Download Address: 0xc0008000, Download Filesize:0x498cd4
Checksum is being calculated.....Checksum O.K.

NAND erase: device 0 offset 0x500000, size 0x500000
Erasing at 0x9e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x500000, size 0x498cd4

Writing data at 0x998800 -- 100% complete.
4820180 bytes written: OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 6
OTG cable Connected!
Now, Waiting for DNW to transmit data

Now, Downloading [ADDRESS:0x40008000,TOTAL:0x9ccc600]
Please waiting ............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Download Done!!
Download Address: 0x40008000, Download Filesize:0x9ccc600
Checksum is being calculated.............................................................................................................................................................Checksum O.K.

NAND erase: device 0 offset 0xa00000, size 0x3f600000
Skipping bad block at  0x148a0000                                            
Erasing at 0x3ffe0000 -- 100% complete.
OK

NAND write: device 0 offset 0xa00000, size 0x9ccc600

Writing data at 0xa20b800 -- 100% complete.
164414976 bytes written: OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 4
OTG cable Connected!
Now, Waiting for DNW to transmit data

Now, Downloading [ADDRESS:0xc0008000,TOTAL:0x177000]
Please waiting .......................Download Done!!
Download Address: 0xc0008000, Download Filesize:0x177000
Checksum is being calculated..Checksum O.K.

NAND erase: device 0 offset 0x200000, size 0x300000
Erasing at 0x4e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x200000, size 0x177000

Writing data at 0x376800 -- 100% complete.
1536000 bytes written: OK

#####    Boot for TQ210 Main Menu       #####
#####     EmbedSky USB download mode     #####

[1] Download bootloader (u-boot or bootimage) to Nand Flash
[2] Download WinCE NK image (NK.bin) to Nand Flash
[3] Download Linux Kernel (zImage.bin) to Nand Flash
[4] Download LOGO Picture (logo.bin) to Nand  Flash
[5] Download UBIFS image (root.ubi) to Nand Flash
[6] Download YAFFS image (root.bin) to Nand Flash
[7] Download Program to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program
[n] Enter TFTP download mode menu
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[u] Download bootloader to SD Card
Enter your selection: 埬?8??

看看参数里那个地址对不
下载的时候要用前面那个“USB下载”选项

地址是对的，也是用前面那个下载的