无法进入WINCE

大家好，我用2440的核心板自己设计的底板，然后把wince的镜像下到板子里去，无法进入wince系统，串口打印的信息如下：

##### EmbedSky Boot #####


##### Eboot for TQ2440/SKY2440 #####
#####     www.embedsky.net     #####

Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 2.4 Built Aug 21 2010

Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.

Initiating image launch in 1 seconds.  0 seconds.
Launching image from boot media ...
OEMPlatformInit: IMAGE_TYPE_RAMIMAGE
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x4
RAM image 0xa 0x80200003
+=OEMVerifyMemory+ dwStartAddr:0x8022dab4  dwLength:0x4
RAM image 0xa 0x8022dab7
waitforconnect
INFO: OEMLaunch: Jumping to Physical Address 0x3022DAB4h (Virtual Address 0x8022DAB4h)...


Windows CE Kernel for ARM (Thumb Enabled) Built on Aug  4 2008 at 18:38:38
ProcessorType=0920  Revision=0
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 8022d970
+OEMInit
DCache: 8 sets, 64 ways, 32 line size, 16384 size
ICache: 8 sets, 64 ways, 32 line size, 16384 size
InitDisplay:320*240
OALKitlStart : NONE
-OEMInit
Sp=ffffc7cc
OEMIoControl: Unsupported Code 0x10100b4 - device 0x0101 func 45
OEMIoControl: Unsupported Code 0x101008c - device 0x0101 func 35
FMD_OEMIoControl: unrecognized IOCTL (0x71c24).
OEMIoControl: Unsupported Code 0x1010118 - device 0x0101 func 70
OEMIoControl: Unsupported Code 0x10100cc - device 0x0101 func 51
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
OEMIoControl: Unsupported Code 0x10100c4 - device 0x0101 func 49
OEMIoControl: Unsupported Code 0x10100c4 - device 0x0101 func 49
INFO: CReg2440Uart::CReg2440Uart using processor frequency reported by the OAL (66666666).
INFO: CReg2440Uart::CReg2440Uart using processor frequency reported by the OAL (66666666).
I2C Init
IIC IRQ mapping: [IRQ:27->sysIRQ:20].
INFO: WAVEDEV.DLL: SetI2SClockRate:  Using processor frequency reported by the OAL (66666666).
Prescaler:3
OEMIoControl: Unsupported Code 0x10100d0 - device 0x0101 func 52
OEMIoControl: Unsupported Code 0x10100f8 - device 0x0101 func 62
VBridge:: VB_INITIALIZED returns [0]

VMini:: VBridge is not initialized!   Bail out..
<Davicom DM9000 driver v3.2.7 for WinCE 4.2/5.0>
<DM9:++MiniportIntialize>
[dm9: Tries to map io space with 20000300
[dm9: The mapped address is 2C0300
[dm9: Chip signature is 29282B00
DM9 Exception Level(1)Unknown deviceDM9 Exception Level(0)Device errorCAM clock:24000000
CamClockOn = 1
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
Camera::Product id is 0xffff
Camera:: OV9650 initialize is faile
CAMERA.DLL::InterruptThread Initialized.
CAMERA: CIS_Open
CIS: IOCTL_POWER_CAPABILITIES
CAMERA: CIS_Open
CAMERA: CIS_Close
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\AFD). Driver cannot be unloaded.
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\PPP). Driver cannot be unloaded.
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\TELNETD). Driver cannot be unloaded.
HW_USBClocks::D0
GPIO Initialize ...OK !!!
Key: DLL_PROCESS_ATTACH.
>>> EINT_initalization address..set..
::: EINT_InitializeAddresses - Success
INFO: EINTKey: Mapped Irq 0x20 to SysIntr 0x1b.
::: KEY_Init Sucessfully!
SDHCardDetectIstThread: CardPresent !!!
SDHCardDetectIstThread: SDHCDIndicateSlotStateChange !!!
S3C2440DISP::S3C2440DISP
OEMIoControl: Unsupported Code 0x10100fc - device 0x0101 func 63
S3C2440DISP::SetMode
Lyg.p: Layout Manager successfully initialized to  2
Maximum Allowed Error 7:
CamClockOn = 0
Explorer(V2.0) taskbar thread started.
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9
OEMIoControl: Unsupported Code 0x1010024 - device 0x0101 func 9：
：
：
请问大家这是为什么啊。

要把解决方法贴出来啊