求助: WINCE NK.bin烧写到TQ2440开发板后无法启动

我原来用的是3.5寸的屏，现在换了4.3寸的屏。烧写NK_Q43_3Serial_20100603.bin（光盘里的）后，开发板无法启动。
打印信息如下：
  Enter your selection: U

USB host is connected. Waiting a download.

Addr: 0xC000000 ; Size: 0x1D947D9
Read Bin Files StartAddr:0x80200000 ; Length: 0x1DF5D90

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000  Length=0x1df5d90
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x1df5d90
RAM image 0xa 0x81ff5d8f
rom_offset=0x0.
ROMHDR at Address 80200044h
+WriteOSImageToBootMedia: g_dwTocEntry =1, ImageStart: 0x80200000, ImageLength: 0x1df5d90, LaunchAddr:0x80201000
INFO: OEMLaunch: Found chain extenstion: '' @ 0x80200000
Writing single region/multi-region update, dwBINFSPartLength: 31415696
CreatePartition: Enter CreatePartition for 0x21.
LastLogSector: Last log sector is: 0x7eeff.
CreatePartition: Start = 0x1100, Num = 0xf000.
WriteMBR: MBR block = 0x10.
WriteData: Start = 0x0, Length = 0x1df5d90.
Updateded TOC!
CreatePartition: Enter CreatePartition for 0xb.
FindFreeSector: FreeSector is: 0x10100 after processing part 0x21.
CreatePartition: Num sectors set to 0x6e900 to allow for compaction blocks.
CreatePartition: Start = 0x10100, Num = 0x6e900.
WriteMBR: MBR block = 0x10.
TOC {
dwSignature: 0x434F544E
BootCfg {
  ConfigFlags: 0x2830
  BootDelay: 0x1
  ImageIndex: 1
  IP: 192.168.1.6
  MAC Address: 10:23:45:67:89:AB
  Port: 0.0.0.0
  SubnetMask: 255.255.255.0
}
ID[0] {
  dwVersion: 0x60000
  dwSignature: 0x45424F54
  String: 'eboot.nb0'
  dwImageType: 0x2
  dwTtlSectors: 0x400
  dwLoadAddress: 0x80038000
  dwJumpAddress: 0x80038000
  dwStoreOffset: 0x0
  sgList[0].dwSector: 0x400
  sgList[0].dwLength: 0x400
}
ID[1] {
  dwVersion: 0x1
  dwSignature: 0x43465348
  String: ''
  dwImageType: 0x2
  dwTtlSectors: 0xEFAF
  dwLoadAddress: 0x80200000
  dwJumpAddress: 0x80201000
  dwStoreOffset: 0x0
  sgList[0].dwSector: 0x2100
  sgList[0].dwLength: 0xEFAF
}
chainInfo.dwLoadAddress: 0X00000000
chainInfo.dwFlashAddress: 0X00000000
chainInfo.dwLength: 0X00000000
}
waitforconnect
INFO: OEMLaunch: Jumping to Physical Address 0x30201000h (Virtual Address 0x80201000h)...

C


重新启动后
##### Eboot for TQ2440/SKY2440 #####
#####     www.embedsky.net     #####

Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 6.0 Built Jan 26 2010

Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.

Initiating image launch in 0 seconds.
Launching image from boot media ...
OEMPlatformInit: IMAGE_TYPE_RAMIMAGE
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x4
RAM image 0xa 0x80200003
+=OEMVerifyMemory+ dwStartAddr:0x80201000  dwLength:0x4
RAM image 0xa 0x80201003
waitforconnect
INFO: OEMLaunch: Jumping to Physical Address 0x30201000h (Virtual Address 0x80201000h)...

C

然后屏幕就显示logo，CE无法正常启动，请问如何解决？

完全格式化一下，在烧写看看

2# shufexiu


我试了一下，还是一样，无法正常启动.

我的操作如下：
从NOR启动

9 完全格式化
1  烧写 TQ2440_CD\出厂烧录镜像合集\奇美4.3寸屏的镜像\U-boot\u-boot_W43_20091031.bin
1  烧写 TQ2440_CD\出厂烧录镜像合集\奇美4.3寸屏的镜像\WinCE\STEPLDR_20100120.nb1
2  烧写 TQ2440_CD\出厂烧录镜像合集\奇美4.3寸屏的镜像\WinCE\EBOOT_Q43_20100120.nb0

关机 按住空格从nand启动

命令 b>>9>>u

烧写TQ2440_CD\出厂烧录镜像合集\奇美4.3寸屏的镜像\WinCE\CE5.0\NK_QW43_3Serial_20091224.bin

3# FPS_365


底板自己设计的？

4# embedsky_lxt


不是自己设计的，都是原厂的。

问题已解决

FPS_365 发表于 2011-4-1 14:35
问题已解决

WINCE NK.bin烧写到TQ2440开发板后无法启动，请问楼主这个怎么解决的啊

laughing19 发表于 2013-11-12 15:48
WINCE NK.bin烧写到TQ2440开发板后无法启动，请问楼主这个怎么解决的啊

重新开贴说你的问题吧。

可否共享下解决方法！