TQ2440不能烧写NK

本人是64M版本的TQ2440,更新到最新的UBOOT,EBOOT后,在下载WINCE 6.0的NK时出现如下错误:

Enter your selection: u

USB host is connected. Waiting a download.

Addr: 0x32000000 ; Size: 0x1EB87D9
Read Bin Files StartAddr:0x80200000 ; Length: 0x1F2A08C

Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000  Length=0x1f2a08c
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000  dwLength:0x1f2a08c
RAM image 0xa 0x8212a08b
+WriteOSImageToBootMedia: g_dwTocEntry =1, ImageStart: 0x0, ImageLength: 0x0, LaunchAddr:0x0
Writing single region/multi-region update, dwBINFSPartLength: 32678028
OpenPartition: Invalid MBR.  Formatting flash.
Enter TQ2440 FastLowLevelFormat [0x0, 0x1ff].
Format TQ2440 Nand Flash: found a bad block (0x0) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x1) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x2) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x3) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x4) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x5) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x6) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x7) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x8) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x9) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xa) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xb) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xc) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xd) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xe) - skipping...
Format TQ2440 Nand Flash: found a bad block (0xf) - skipping...
Format TQ2440 Nand Flash: ...erase complete.
WriteMBR: MBR block = 0x10.
BP_FastLowLevelFormat: Done.

CreatePartition: Enter CreatePartition for 0x21.
LastLogSector: Last log sector is: 0x1efff.
CreatePartition: Start = 0x1100, Num = 0xfa00.
WriteMBR: MBR block = 0x10.
WriteData: Start = 0x0, Length = 0x1f2a08c.
CreatePartition: Enter CreatePartition for 0xb.
FindFreeSector: FreeSector is: 0x10b00 after processing part 0x21.
CreatePartition: Num sectors set to 0xe300 to allow for compaction blocks.
CreatePartition: Start = 0x10b00, Num = 0xe300.
WriteMBR: MBR block = 0x10.
INFO: using TOC[1] dwJumpAddress: 0x0
waitforconnect
ERROR:OALVAtoPA: invalid virtual address 0x00000000
INFO: OEMLaunch: Jumping to Physical Address 0x0h (Virtual Address 0x0h)...
文件没有下载到NAND中去,请教解决方法.

好不容易有人回复,还被禁了.我已经搞定了,跟电脑有关,用以前的旧电脑已经烧写完成.